Description

Products You May Like

• FWW DVD PROFILE: TAGE FRID

  $19.95 $11.97 0 review(s)

  
  

  “The next best thing to a private lesson” Tage Frid, known as the "Dean of American Woodworking," helped thousands learn woodworking over his 50-year career as a woodworker, educator, and author. This DVD video is an opportunity to visit the master in his shop and home and listen to him as he shares his wisdom. Never before released in its entirety, this documentary shows Frid as he builds several pieces and discusses how his philosophy of designing around construction plays into his work. Frid also demonstrates such woodworking basics as sharpening a chisel and cabinet scraper as well as how to make multiple spline joints and cut half-blind dovetails. Two bonus segments on laminating in form to make salad servers and veneering a coffee table are also included.

• HANDPLANE BASICS: A BETTER WAY TO USE BENCH PLANES- DVD

  $24.95 $14.97 0 review(s)

  
  

  While bench planes are the most fundamental handplanes in your shop, they also are the most vexing. Ask two woodworkers how to choose, set up and use your bench planes and you'll get three answers. After years of historical research and practical bench experience, Editor Christopher Schwarz has found a way to simplify the convoluted bench plane system so you can think for yourself when it comes to these tools. After viewing this DVD you'll know how to select the right size plane for your work. You'll know how to sharpen and set it up so it does the job at hand. And you'll learn how to use the plane so you make perfectly flat and gleaming panels (with the minimum amount of effort). This DVD doesn't simply spout off a new idiosyncratic way to work with bench planes. Instead Schwarz explains how all the systems work so you can immediately see their strengths and weaknesses and exploit them so you'll do better work. "Handplane Basics" puts into practice all of the principles explained in the story "Bench Planes: The System of Three" in this issue of Woodworking Magazine and dives further into the topics of sharpening, setup and use. If you are confused or frustrated by your bench planes, this DVD is just the ticket.

• WOODCARVING #1: SHARPENING TECHNIQUES - DVD

  $32.50 $19.50 0 review(s)

  
  

  Bench side instruction on how to make a gouge do more than you may have thought possible. Chris starts with a new tool and thoughtfully walks you through all the steps of preparation to finally achieve that desired cutting edge. You are guided through the maze of available chisels, Chris answers the how's and whys and suggests where to start when it comes to acquiring tools. Included in this dvd are a few of the practises Chris was taught during his apprenticeship that are not widely known yet I consider revolutionary as per sharpening a gouge.

• TILING COUNTERTOPS - DVD

  $19.95 $11.97 0 review(s)

  
  

  “Get traditional results with modern materials.” Ceramic-tile countertops can be as attractive as they are practical. And a small countertop is the perfect introduction to the techniques of tiling. With a bathroom as his job site, professional tilesetter Michael Byrne demonstrates how to get traditional results with modern materials. You'll learn how to work with both backer-board and mortar-bed substrates, how to trim tile around a sink, and how to detail your countertop for a clean, crisp look. If this is your first go at tilesetting, Byrne gives you the confidence to see the job through. If you're an experienced tilesetter, you'll find this tape full of new ideas to bring to your next tile job. Learn how to: - lay out tile for an orderly appearance in any shaped space - determine the proper consistency and coverage for thinset - cut tile, using a snap cutter, biters and a wet saw - finish a grout job that requires no next-day scrubbing

• ROUGH TO READY - DVD

  $29.95 $17.97 0 review(s)

  
  

  Subtitle: “Bench-side instruction on preparing rough lumber with hand tools.“ In this video, Rob Cosman demonstrates how to prepare rough lumber with hand tools. He covers flattening, making the board square and true, and how to use a shooting board. Includes many useful tips on sharpening, planing, gauges, etc.

• FWW: VIDEO WORKSHOP SERIES #2 MONSTER WORKBENCH

  $29.95 $17.97 0 review(s)

  
  

  In this video workshop, I'll show you step-by-step how to make a durable workbench designed to last a lifetime. The construction is straightforward, the trick is managing the massive amount of lumber. Tune in to watch the series for a collection of useful tips and techniques. This solid, versatile workbench works well for hand or power tool use. The large, thick top sits on a sturdy base held together by both glued and knockdown mortise-and-tenon joints. To hold your work, there is a twin-screw vise, and plenty of dog holes for holdfasts. This series includes: More than 30 minutes of video instruction Useful techniques for cutting mortises and tenons, installing hardware, and using hand tools. A digital SketchUp plan that's available in our plan store