Description

Products You May Like

• WOOD FINISHING BASICS - DVD

  $19.95 $11.97 0 review(s)

  
  

  Repair dents and gouges, choose the right sandpaper, brush on a perfect finish, set up a siimple spray booth, use all types of spray guns. Includes applying a finish by rag, brush or gun.

• TILING COUNTERTOPS - DVD

  $19.95 $11.97 0 review(s)

  
  

  “Get traditional results with modern materials.” Ceramic-tile countertops can be as attractive as they are practical. And a small countertop is the perfect introduction to the techniques of tiling. With a bathroom as his job site, professional tilesetter Michael Byrne demonstrates how to get traditional results with modern materials. You'll learn how to work with both backer-board and mortar-bed substrates, how to trim tile around a sink, and how to detail your countertop for a clean, crisp look. If this is your first go at tilesetting, Byrne gives you the confidence to see the job through. If you're an experienced tilesetter, you'll find this tape full of new ideas to bring to your next tile job. Learn how to: - lay out tile for an orderly appearance in any shaped space - determine the proper consistency and coverage for thinset - cut tile, using a snap cutter, biters and a wet saw - finish a grout job that requires no next-day scrubbing

• BASIC DOOR CONSTRUCTION:CABINETS Vidwood 104 - DVD

  $19.95 $11.97 0 review(s)

  
  

  Demonstrates the differences between flush, lip, and overlay door. Tolerances, allowances, and dimensions for each type of door are presented. This DVD will show you how to begin with an opening and progress through the steps required to build a door. Demonstrates how to rout doors for 3/8 lip styling and how to make small glass molding safely. Also covers plywood doors with decorative molding trim and raised panel doors without complex joinery.

• DOVETAIL A DRAWER - DVD#

  $19.95 $11.97 0 review(s)

  
  

  If it's properly fitting drawers you're after, this is the video workshop for you. Professional cabinetmaker Frank Klausz cuts quick, precise dovetails without jigs or templates, then glues up and fits the finished drawer. You will learn about: - dovetail drawer anatomy - transferring dimensions from the scale drawing to a full-scale "story-pole" - choosing lumber - marking out, ripping and crosscutting drawer parts - marking out the dovetails and pins - hand sawing the pins and tails and chopping out the waste - gluing up - applying finishing touches with a smooth plane DVD also available as a video, see item 22-1.

• ADVANCED DOOR CONSTRUCTION: CABINETS VW105 - DVD

  $19.95 $11.97 0 review(s)

  
  

  This DVD is devoted to the more technical aspects of door construction. Covers haunched mortise and tenon joinery on the table and radial arm saw. Illustrates an easy method of laying out the mortise and tenon with handtools. Dr.Cliffe then covers raised panel cutting together with gluing and clamping. The DVD concludes with a demonstration of fitting and hinging techniques for a flush door and an overlay door.

• HANDPLANE BASICS: A BETTER WAY TO USE BENCH PLANES- DVD

  $24.95 $14.97 0 review(s)

  
  

  While bench planes are the most fundamental handplanes in your shop, they also are the most vexing. Ask two woodworkers how to choose, set up and use your bench planes and you'll get three answers. After years of historical research and practical bench experience, Editor Christopher Schwarz has found a way to simplify the convoluted bench plane system so you can think for yourself when it comes to these tools. After viewing this DVD you'll know how to select the right size plane for your work. You'll know how to sharpen and set it up so it does the job at hand. And you'll learn how to use the plane so you make perfectly flat and gleaming panels (with the minimum amount of effort). This DVD doesn't simply spout off a new idiosyncratic way to work with bench planes. Instead Schwarz explains how all the systems work so you can immediately see their strengths and weaknesses and exploit them so you'll do better work. "Handplane Basics" puts into practice all of the principles explained in the story "Bench Planes: The System of Three" in this issue of Woodworking Magazine and dives further into the topics of sharpening, setup and use. If you are confused or frustrated by your bench planes, this DVD is just the ticket.