Description

Products You May Like

• SCRAPING WOOD - DVD

  $37.95 $22.77 0 review(s)

  
  

  Bench side instruction on tuning, sharpening and using scraping tools. This is perhaps one of the most anticipated DVDs Rob has made. Many people own scraping tools but don't know how to use them and the "how to" information is scarce. This DVD will teach you how to sharpen and use card scrapers, cabinet scrapers and scraper planes. In a step-by-step fashion Rob will carefully walk you through explaining and demonstrating along the way. With figured wood, scraping can be the most efficient way to process and prepare the surface. Without the cost, dust and noise of power sanding, removing a sub one thou shaving from figured wood can be as much fun as the finished product. Over 1 1/2 hours of personal instruction from the bench of one of today's leading hand tool coaches.

• BOWL TURNING - DVD

  $19.95 $11.97 0 review(s)

  
  

  Del Stubbs shows you how to turn beautiful bowls and plates. You can start with dry lumber or with green wood you cut yourself. The camera zooms in close to see the careful contact of edge on wood and then moves back so you can study various tool positions, grips and stances. You will learn about: cutting tool types and modification of standard tools grinding and honing chisels gripping various turning tools mounting bowl blanks and roughing out the shape modifying a standard lathe controlling warp in the thin wall of a bowl cutting into endgrain designing bowl forms DVD, also available as a video, see item 22-3.

• DRYWALL: HANGING AND TAPING - DVD

  $19.95 $11.97 0 review(s)

  
  

  Learn to take accurate measurements, cut and hang panels efficiently, handle cathedral ceilings and curved walls, tape and finish to reduce sanding, how to hold and use tools, prepare the walls for paint, correct mistakes and make repairs. DVD NTSC

• HANDPLANE BASICS: A BETTER WAY TO USE BENCH PLANES- DVD

  $24.95 $14.97 0 review(s)

  
  

  While bench planes are the most fundamental handplanes in your shop, they also are the most vexing. Ask two woodworkers how to choose, set up and use your bench planes and you'll get three answers. After years of historical research and practical bench experience, Editor Christopher Schwarz has found a way to simplify the convoluted bench plane system so you can think for yourself when it comes to these tools. After viewing this DVD you'll know how to select the right size plane for your work. You'll know how to sharpen and set it up so it does the job at hand. And you'll learn how to use the plane so you make perfectly flat and gleaming panels (with the minimum amount of effort). This DVD doesn't simply spout off a new idiosyncratic way to work with bench planes. Instead Schwarz explains how all the systems work so you can immediately see their strengths and weaknesses and exploit them so you'll do better work. "Handplane Basics" puts into practice all of the principles explained in the story "Bench Planes: The System of Three" in this issue of Woodworking Magazine and dives further into the topics of sharpening, setup and use. If you are confused or frustrated by your bench planes, this DVD is just the ticket.

• WOODCARVING #3: ORNAMENTAL CARVING - DVD

  $39.95 $23.97 0 review(s)

  
  

  Over 2 hours of expert instruction in carving an attractive and adaptable leaf decoration. The 2 disk DVD also highlights holding and using woodcarving tools correctly and efficiently. Fundamental woodcarving cuts: running, stabbing, sliding and sweeping!

• 3 TECHNIQUES ON 1 DVD, Vol. 1

  $22.95 $13.77 0 review(s)

  
  

  This DVD contains instructions on the following woodworking techniques: Ogee Bracket Feet: This method begins with the layout of the pattern and cove cutting at the table saw. We show you how to set up the mitering of the feet so that each foot matches in design & size. Cabriole Leg: In this technique we walk you through the method to build these graceful legs. Step by step, you learn the correct way to lay out the pattern, the proper cutting sequence at the band saw and how to hand shape the overall design as well as turn the cup of the foot at the lathe. There is also a Bonus included – we show you the process to create these legs using only hand tools!! Along the way we point out a number of simple methods and ideas to insure success. Raised Panel Door: We will begin with an understanding of the parts of a door and how one obtains the sizes for those parts. We show you how to set up and complete the mortise and tenon joint as well as a specific method of creating the raised panel at the table saw.